Clik here to view.
EVAL-ADP5040 Docs
Hi, I wanted to use the ADP5040 Eval board, and unfortunately there is no documentation about this board avaiblable.Can someone help me out? Kindly regardsJan
View ArticleADP1048 Incompatibility to SC18IS600 ?
Dear all, we are trying to communicate with the ADP over an I²C/SPI Bridge (SC18IS600, NXP). In my opinion it should work fine. Without activating the PFC/Boost function (PSON OFF) the communication...
View ArticleClik here to view.
NDS&PSRR data of ADP1740/41
Hello, I only found the NSD & PSRR data about ADP1740/1741 in datasheet as shown below.Could you please provide NSD & PSRR graph data of ADP1740/1741 for the following conditions? - V_dropout...
View ArticleADP5090 MPPT Calculate
Dear All:How do Iknowthe ADP5090 Max MPPT value is how much? Also, ifIknew solar panel max MPPT point, how do I put him in the ADP5090 adjusted to synchronize withSolar? have any document can provide...
View ArticleAM Signal generation
Hello Is there any ready AM Signal Generator at ADISimPE? Thanks and best regardsHakan
View ArticleIs a disabled ADP5071 safe against reverse currents?
Hi, I have a ADP5071 that is used for a +/-15 V supply. For some tests I would like to disable the ADP5071 by pulling the EN low, and supply the +/-15 V from an external source. Is it safe to do so, or...
View ArticleCan i use continuous read mode in ADM1166 or not?? if yes please tell me the...
I am trying to read ADM1166 data in continuous read mode. But i am not able to achieve it. So anyone can tell me whats the problem with it??
View ArticleClik here to view.
About ADM660 voltage output delay time
Hi, All. In the circuit shown in the figure below, please tell us about the delay time until the output rising from the input rise of the ADM660. Best Regards,Laliberte
View ArticleADA2200 simulation
I want to simulate the ADA2200 synchronous detector. I have downloaded the SPICE model from the analog.com webpage. I see that there are subcircuits defined there. It would be great if I could see the...
View ArticleClik here to view.
For ADM809L, what will the output voltage on RESET pin be when it is sourcing...
The ADM809L datasheet specifies the maximum output current of RESET pin is 20mA. So I assume it is safe to source 10mA for RESET pin. I want to use this pin to drive an opto-coupler which need...
View ArticleClik here to view.
MPPT and Charge Management IC with output current up 600mA ?
Hi, I'm looking for a IC for solar power harvesting, 1 cell lithium battery charging support and power loading share.Something like ADP5090 but supporting output current to system up to 600mA. Is there...
View ArticleClik here to view.
Connecting ADP5092 with a Wireless Power Receiver
Hello-We need to integrate Wireless Power Receiver (BQ51051B) in our design for wireless sensor that uses ADP5092 to charge a 3.7v Li-Po battery from solar cells. The battery is connected directly to...
View ArticleClik here to view.
LDO as current source
Hi all,I need a negative current source of about 180 mA, I found that we can use LDOs to creat current sources, is there any document that explains the concept?I already use the ADP7182 in my circuit,...
View ArticleBattery charger project question
Hi. We have a project is for car Battery charger application. System function SPEC on below. Please kindly help us check AD8450 + ADP1972 or 74 can meet SPEC or not. Vin: DC24V car battery (DC18~30V)....
View ArticleClik here to view.
URGENT support required with ADP1048-600-EVALZ
My ADP1048-600-EVALZ evaluation board has failed and has damaged my electronic load bank in the process. After applying AC power to the board the input fuse blew and the load bank shutdown. My...
View ArticleClik here to view.
ADP5061/2 THR temperature detection
Dear Sir,ADP5601/2 has one pin THR design for battery charging temperature detection, if i use this P/N to sense battery temperature, do i need to tie external NTC to my battery pack?
View ArticleClik here to view.
I am able to read adn4605 some register correctly communiting to device with...
i pull up to high but failed too. i read the registers(0x54-0x7b),it shows 0x00 0x01 0x02...0x27 can u tell me where is the problem? thanks
View ArticleUsage of ACSNS pin on adp1046 LLC Half bridge resonant mode.
We have delevoped an evaluation board based on ADP1046 Half bridge resonant mode LLC converter according to UG-768 Analog Devices EVB schematics but for application . same as stated at the UG-768...
View ArticleClik here to view.
AD5522 SDO in 3-state/hi-impedance?
HelloCould you clarify more regarding the SDO pin? When is the SDO pin in tristate? What is the SDO pin state when the sync/ signal is in “high” level? From the spec table we can see a tri-state...
View ArticleClik here to view.
ADP5589 question
Dear Sir,ADP5589 have driver for windows10 mobile?ADP5589 have EVM document? Thanks.
View Article