Quantcast
Channel: EngineerZone : Unanswered Discussions - Power By Linear
Browsing all 2027 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Hi, I try to use ADIsimPE with fresh installed Win10 prof 64Bit, but error...

View Article


Image may be NSFW.
Clik here to view.

ADP5052 LDO

Hi I have a question ADP5052 LDO. When LDO is not used in ADP 5052,Is PVIN 5 OK even with OPEN?(EN pin is connected to 0 V) Best RegardsHOD

View Article


Image may be NSFW.
Clik here to view.

ADP5090-2-EVALZ very inefficient?

Dear reader, For a school project we want to use the ADP5090-2-EVALZ as a power source for our Ultra Low Power project. The problem is that the kit doesn't seem to function as a high efficiency...

View Article

Image may be NSFW.
Clik here to view.

ADM660

Hi, All. Was wondering if i could get the pspice model of ADM660.Thanks

View Article

Image may be NSFW.
Clik here to view.

ADM660

was wondering if i could get the pspice model of ADM660.Thanks

View Article


Vin_on on ADP1048W

Hello everyone, my dear friends! I assembled a PFC test card and a separate control board on the ADP1048W and now I want to test it by applying a voltage of 15-20 volts to the input. I have entered all...

View Article

Image may be NSFW.
Clik here to view.

Why do some LTC2943 registers read as 0x0411

We are using an LTC2943 to monitor the charging of a lithium battery.  If we read from certain pairs of registers too often, or back-to-back, the device returns a value of 0x0411.   In particular, at...

View Article

Using a ADN8835 for a TEC in an image sensor

Would the above part be suitable for use with a TEC in an image sensor device (InGaAs)?Thanks

View Article


Image may be NSFW.
Clik here to view.

where i can get LTC7004 simulation

We are using LTC7004 for one of our project for switching ON/OFF the load.we can not simulate above circuit through LTspicecan u give me feedback above circuit working fine ??i have set OVLO is 50V and...

View Article


Image may be NSFW.
Clik here to view.

How do i link the Anlog Devices supplied AD630.cir file into my...

How do i link the Anlog Devices supplied AD630.cir file into my schematic/simulation using ADIsimPE

View Article

Image may be NSFW.
Clik here to view.

ADP5052 output

 the back R259 R265 R270 R274 used 0Ω,why? I can't understand the way, could you tell me ? Thanks !

View Article

Image may be NSFW.
Clik here to view.

Force ADP5062 to do power off cycle

Is it possible to do hard power off cycle with ADP5062 charger. We do have a need to be able to do a complete power off reset to the board and restore the situation without need to plug in the external...

View Article

Image may be NSFW.
Clik here to view.

Hi, I try to use ADIsimPE with fresh installed Win10 prof 64Bit, but error...

View Article


Image may be NSFW.
Clik here to view.

output voltage tolerance calculation ADP1762-ADJ

Hello, I would like use ADP1762 adjustable LDO.My application needs power supply +0.975V +-0.025V (≙ accuracy 2.56%) at 1.7A.Supply voltage tolerance sourced to LDO input is +1.8V +-0.1V.Ambient...

View Article

Image may be NSFW.
Clik here to view.

ADP5080 Gerber file and some questions about spec

Hi ADI Expert, Can you please kindly share the gerber file of ADP5080 to me? Thanks!! And I have some questions about ADP5080's spec, can you please kindly help to answer my questions as below : 1....

View Article


Image may be NSFW.
Clik here to view.

ADP5054-EVALZ

Hi,I'd like to know about ADP5054-EVALZ.Does it be possible to enable all channels with max load written in  UG-816 Figure 12   @25'C?It was not acceptable on ADP505x_BuckDesigner because of junction...

View Article

Image may be NSFW.
Clik here to view.

Hi, I try to use ADIsimPE with fresh installed Win10 prof 64Bit, but error...

View Article


Image may be NSFW.
Clik here to view.

ADIsimPE output noise simulation

Hello guys, I want to simulate the output noise of my circuit, but when I configure the simulation and run it, the software does nothing, I dont know what am I doing wrong but I cant manage to get the...

View Article

Image may be NSFW.
Clik here to view.

ADP5091 function

Hi  I have a question regarding the storage function of the ADP5901 Overcharge prevention voltage 3.7 VOverdischarge prevention voltage 3.0 V Connect to the SETSD and TERM terminals if you want to How...

View Article

AD734 as a Sine Function generator?

Hi,AD534 can be use as a sine function generator (fig. 22 from datasheet). Can I use AD734 as a sine function generator since there is no reference circuit that shows this IC can be use as a sine...

View Article
Browsing all 2027 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>