Quantcast
Channel: EngineerZone : Unanswered Discussions - Power By Linear
Browsing all 2027 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

EVAL-ADP5075 documentation

Documentation is missing in the eval board page. Could you provide it? Thanks.

View Article


About ADP2138/39

Hi there,I have questions about ADP2138/ADP2129.Regarding, ENpin and Modepin, these pins have either internal pull up  or pull down?If so, please let me know whether it is pull-up or pull-down...

View Article


UL approval of Current limiter IC

Hello, I am in search of a current limiter IC for one of my application. I can see component like ADM1270, Just wanted  to know about the UL approval ? Is there any chip in the current limter/Hot swap...

View Article

Noise problem with a REF01 with booster transistor

Hello all,I have a noise problem at an oscillator starting at abt 100 kHz up to abt 1 MHz offset from the carrier (see picture).I measured the spectrum of the power supply - and there is a remarkable...

View Article

Image may be NSFW.
Clik here to view.

ADP1046A Current Sharing Detail Description

Hi, Several of ADP1046A are planned to be used in parallel for increasing of power supply output current. The ADP1046A current sharing feature can be used for the task. But I can't find any detailed...

View Article


Image may be NSFW.
Clik here to view.

EVAL-ADP5074 documentation

As previously with eval kit of the ADP5075, documentation is missing in the web page. Came on folks, that sends a negative message to prospective users of the part. At list to me it does. Anyway, can...

View Article

Image may be NSFW.
Clik here to view.

ADM13307 , Tj Spec

Hi Sir,     We are going to design the ADM13307 , but i can't find the Tj spec in the datasheet , could you help to check the spec? Thanks for your help.

View Article

Image may be NSFW.
Clik here to view.

ADP5091 5V OUTPUT

I have a question about ADP 5091.Use the VID terminal to select the output of the regulator from 1.5 V to 3.6 V.However, the graph on the datasheet shows the efficiency at 5 V output.Is it impossible...

View Article


AD633 noise SImetrix model doesn't match datasheet

Hi everyone, I am trying to do a noise simulation of a circuit using the AD633 low-cost analog multiplier. As a first check on my results, I have wired the multiplier in ADIsimPE (Simetrix) as in the...

View Article


Complete Scheme of RF PA Supply using Envelope Tracking Devices

I am designing an Envelope Tracking System and came across some devices (e.g. HMC1120 and other alternatives) which are capable of doing so.Request some pointers for complete...

View Article

Image may be NSFW.
Clik here to view.

ADP5062 Overcharging

Hi,We're using an ADP5062 in one of our products to charge a Li-Ion cell. Most of the time it works perfectly, but in some situations, it will keep charging the battery until the protection module...

View Article

Image may be NSFW.
Clik here to view.

ADP5350 "Resistance Thresholds by Battery Temperature"

I have read the ADP 5350 datasheet."Resistance Thresholds by Battery Temperature" is stated,Could you please tell me the data at RNTC = 10 kΩ, BETA_NTC = 3370 K? Best regards

View Article

Johnson noise amplification and filter circuit design review

Dear EZ community, I have been working on a Spice deck of a Johnson noise amplifier and filter circuit. Its purpose is to simulate the results of a research project to demonstrate measurement of...

View Article


Image may be NSFW.
Clik here to view.

ADM1278 power TVS layout guidance

Dear Sir:We have a layout question about ADM1278 After we checked the voltage of ADM1278 Vcc pin from HSC side in the simulation SW, still can see spike voltage, so the TVS should be near to HSC to...

View Article

hi we are designing power section for an FPGA based system...

hiwe are designing power section for an FPGA based system :application(Medical).Q1:        I need to convert 12v Dc voltage into both +150V DC and -150V DC ,the maximum current rating should be 0.5 A....

View Article


Image may be NSFW.
Clik here to view.

Maximum Vout spec of ADP2389/90

What is maximum Vout spec of ADP2389/90 ?I could not find the spec in ADP2389/90 datasheet.Thanks.

View Article

Image may be NSFW.
Clik here to view.

ADP5062 Recharge happening too often

While I was testing and debugging for ADP5062 Overcharging, I noticed that on some units, the recharge cycles are occurring much more frequently than they should. I've attached logs from 2 units...

View Article


Image may be NSFW.
Clik here to view.

troubles with SPICE models of AD8033 and AD8065

hello, i am working with your open SPICE models of AD8033 and AD8065and i am having troubles with the voltage gain characterization. I would like to reproduce the OPEN-LOOP responseas appears in your...

View Article

ADI SimPLL and HMC3716 PFD

Does the latest ADI simPLL  include the HMC3716 phase/freq detector? If not, when will it?

View Article

Image may be NSFW.
Clik here to view.

Ripple Filter Damping Techniques

Found this very useful article by Kevin M. Tompsett on damping of a PSU output...

View Article
Browsing all 2027 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>