Quantcast
Channel: EngineerZone : Unanswered Discussions - Power By Linear
Browsing all 2027 articles
Browse latest View live

ADP7142 Output abnormality

Hello. When chattering occurs at startup input, LDO output will be abnormal.Phenomenon 1  Vin = VoutPhenomenon 2  The voltage is not set.  And VADJ voltage is not 1.2 V...

View Article


problem simulating CD4046 with ADIsimPE

i have been trying to simulate cd4046 with ADIsimPE but the IC just doesnt work at 15V power supply. I have calculated the values of R1,R2, C1 susch that the frequency range is between 32 to 33 Khz. I...

View Article


Image may be NSFW.
Clik here to view.

Timer for detail about ADP5062

Today,I just moved from discussion sled to question sled here due to higher priority than discussion.So please advice me following timer question thanks.Kaos--- Dear Sir/Madam, Our customer is still...

View Article

ADD5211

Hi, Page one of the ADD5211 data sheet states that PWM dimming at 300 Hz, what is the maximum frequency that can be used for PWM dimming? Best Regards.

View Article

Encrypted SPICE AD797 and AD734

Can someone please give me encrypted ADIsimPE files for the AD797 low noise op amp and the AD734 analog multiplier?I have hit the 'too many nodes' limit. SincerelyDaniel H.

View Article


Image may be NSFW.
Clik here to view.

Need help finding LDO for MMIC PA

HI,I need help selecting and configuring low noise LDO for MMIC PA in E-PHEMT process, part#LHA-1+.  PA operates upto 6GHz and will process low phase noise clock source so wanted clean biasing.  Is...

View Article

Image may be NSFW.
Clik here to view.

I see that ADM717x have EN INPUT STANDBY at page 5(4) of datasheet.

I see that ADM717x have EN INPUT STANDBY at page 5(4) of datasheet.And I see that ADM717x have EN INPUT PRECISION, too. But ADM717xhave only one pin EN. How so?

View Article

problem simulating AD736 in ADIsimPE

simulating AD736.I was trying to simulate AD736 rms to DC converter for 200mV input for fastest settling time. I have attached the circuit below. I might have made mistakes in selecting the Cav and Cf...

View Article


problem simulating CD4046 with ADIsimPE

i have been trying to simulate cd4046 with ADIsimPE but the IC just doesnt work at 15V power supply. I have calculated the values of R1,R2, C1 susch that the frequency range is between 32 to 33 Khz. I...

View Article


Image may be NSFW.
Clik here to view.

ADP1972 Fig1 FET symbol

     Is the FET here not NMOS not PMOS?

View Article

generating a chirp signal with the use a PLL with a DDS as a reference

helloNow I'm working on generating a chirp signal in the X band and the C band therefore I want to use a PLL with a DDS as a reference and for that I want to know how to dothank youcordially

View Article

LDO with adjustable current limiting etc. available?

Hi Analog Devices,I have searched your power management products for an LDO with these characteristics: - Single regulator output, adjustable. Preferably up to 20 VDC. Input voltage up to 22 VDC.- 200...

View Article

Image may be NSFW.
Clik here to view.

Interface for Implementing NLMS algorithm in ADAU1452

Hi, I am using ADAU1452 SigmaDSP to implement an algorithm derived from NLMS adaptive algorithm. It is a dual-path algorithm,where it stores the background (shadow) coefficients. It would be helpful if...

View Article


problem simulating AD736 in ADIsimPE

simulating AD736.I was trying to simulate AD736 rms to DC converter for 200mV input for fastest settling time. I have attached the circuit below. I might have made mistakes in selecting the Cav and Cf...

View Article

Image may be NSFW.
Clik here to view.

How's the Vcc voltage drop will reset ADM1278 register?

Hi ADI Expert, When ADM1278 Vcc drop, what's the Vcc voltage threshold which may make ADM1278 register be cleaned/reset? May I know the possible range? I would like to know whether is possible my...

View Article


generating a chirp signal with the use a PLL with a DDS as a reference

helloNow I'm working on generating a chirp signal in the X band and the C band therefore I want to use a PLL with a DDS as a reference and for that I want to know how to dothank youcordially

View Article

Image may be NSFW.
Clik here to view.

ADP5063 How to configure DIG_IOx as stated in table 49 in datasheet?

Hi,recently I started to integrate ADP5063 to my project. Now I stumble on how to reconfigure the DIG_IOx to another option set. We designed our PCB to use "1001" configuration, especially with the...

View Article


ADP2442 - VCC load capatibility

Hi i'm using ADP2442 as inverter. I'd like to use VCC-Pin to source a external component. How much current can i sink from the source pin?

View Article

Image may be NSFW.
Clik here to view.

How to use SMBALRT as a simple POWER GOOD?

Hello, I just wana use the pin SMBALRT as a "simple PG" = asseteed if Vout is between POWER_GOOD_ON an OFF.By reading the datasheet It is not clear if:-the PG function can operates even if the ADP1055...

View Article

ADM1278 EVB Board Over 1000W Testing

Dear All:I want to use ADI Demo Board EVAL-ADM1278EBZ to testing power system @12V/90A(1080W). This test will be what kind of problem? the UG-601 ADM1278 demo board user guild show 12V/73A, If I add...

View Article
Browsing all 2027 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>