Clik here to view.
ADM1278 sense Resister setting
Hi Siras below screen, that we use the GUI for connect ADM1278 by I2C interface, that we need to fill in the value about the sense Resistor and can getting the current reporting. my question is if we...
View ArticleSome questions for ADP5062
Can anyone expert reply about this?Thanks ----Dear Sir/Madam, Our customer is studying with your power ADP5062.So he has brought as following questions. I needs your good comment here thanks. Q1)Your...
View ArticleADM691A rechargeble battery
Hello ADM691A datasheet figure 21 says the rechargeble battery.The input power line is connected to battery line and Vout line in figure 21.Is this description typo ? I think that above connection is...
View ArticleClik here to view.
ADA4941-1 .cir
Hi all, Our customer tryed to simulate the ADA4941-1 with ADIsimPE.They downloaded the ADA4941 SPICE Macro Model from web linked page . But the error occured with following error massage."*** ERROR ***...
View ArticleQuestion for your ADP5062 again
Can anyone expert reply about this?This sled seems to broken, so I put this again here. Thanks ----Dear Sir/Madam, Our customer is studying with your power ADP5062.So he has brought as following...
View ArticleClik here to view.
Your EZ condition
Please check your engineer zone sled for the reply function?The question past posted (eg;ADP5062) cannot put the answer there. Thanks Kaos
View ArticleADP5090 MINOP Bias Current and consumption current
HiI ask the MINOP function.I'm through the resistance which connects a MINOP terminal to AGND to use the MINOP function.Or I connect a MINOP terminal to AGND directly because the MINOP function isn't...
View ArticleClik here to view.
ADP5090 Figure 32. D1 diode
I read a datasheet of ADP5090(Rev. C ).Diode D1 which isn't drawn in figure 29 is drawn in figure 32.Does this diode exist inside ADP5090?
View ArticleClik here to view.
ADP5090 Vref tolerance
The tolerance of Vref in ADP5090 is quite large 1.14 to 1.28V. So setting TERM with 1% resistors to not overcharging a Li-ion battery over 4.2V would result in unacceptable variation due to tolerances...
View ArticleADIsimPE Design Tool model for ADP3050
Dear Analog, could you share an ADIsimPE Design Tool model for ADP3050?
View ArticleHMC1060 isolation between output terminals
Hello. I want to know isolation between output terminals.Especially want to know the characteristics in two case.1. When VR4 load fluction, other output(VR1,2,3) behavior.2. When VR4 load fuuction and...
View ArticleWhen does ADP5090 watch Vsys?
A question about a PGOOD signal of ADP5090.Is ADP5090 always watching Vsys? Or is ADP5090 watching Vsys intermittently?In case of the latter, how much is time interval? Can a designer control time...
View ArticleADP5070 max load current
I am trying to figure out, how to increase the load current of the ADP5070CP-EVALZ-ND.Currently I placed a Load-Resistor (100 - 300 Ohm) between +/- 15 Volt output. It seems like -15V shuts down if...
View ArticleClik here to view.
ADP1048
Is it possible to use the ADP1048 with 3 phases rectifier bridge (AC input of 400VAC)? VAC measurement is it adaptable for this voltage? Thank you for your answer. Olivier
View ArticleClik here to view.
generating a chirp signal with the use a PLL with a DDS as a reference
helloNow I'm working on generating a chirp signal in the X band and the C band therefore I want to use a PLL with a DDS as a reference and for that I want to know how to dothank youcordially
View ArticleADP2291
Designed for Imax @ 750mA based on Datasheet (Figure 23 exact, except D1 is 1N5819 instead of BAT1000)Rs = 200mOHMRadj = open MeasurementsVin = 5.9V (Voltage Drop across D1 is 0.301V)Vrs = 15mVVadj =...
View ArticleClik here to view.
ADP1047
HI,I plan to use ADP1047/8 with a 3 Phases AC input.If the passive rectifier output not reach the zero voltage, is that the product will work ? RegardsJ. Domingo
View ArticleAD MPPT IC for Panel e.g SM72442, LT8490
Hello,I am developing a direct battery charger for panels and am looking for single IC systems instead of uC based. What options does AD offer? The preliminary panel specs are 60 - 96 cell panel hence...
View Article