Clik here to view.
AD5522 SDO in 3-state/hi-impedance?
HelloCould you clarify more regarding the SDO pin? When is the SDO pin in tristate? What is the SDO pin state when the sync/ signal is in “high” level? From the spec table we can see a tri-state...
View ArticleClik here to view.
M38510/12801BGA
hello, Please I want to ask about the Lifecycle status for this part M38510/12801BGA ? Regards,Ehab
View ArticleADP1613 high noise on output (400mVpp)
Hello, I designing a power supply +5V and -/+15V with ADP1613 and ADP1614 (+/-15V) for ADAS3022 and DAC LTC2668 from Linear Technology. I use ADP1613 to generate 6.5V from 5V input, then I use LDO to...
View ArticleADM1191 application question
Hello,We would like to design the ADM1191 for POL power monitor application.So far I have three question for this schematic1. SETV pin, if we dont need to setting the alertb, may I floating this pin or...
View ArticleClik here to view.
ADP5052 maximum output voltage when PVIN 5V for channels 3 and 4
I created a custom board to test the ADP5052 buck regulator.The output voltage for the stages I want is good except for 1 channel which does not correctly work untill the input voltage is more than 5V....
View ArticleADP5071 - Maximum Output Currents?
Data sheet maximums say 2.0A positive output and 1.2A negative output, but the ADi Designer (Excel) will only allow 0.9A positive and 0.3A negative ( /-18V out, +12V in, 65C). What am I doing wrong?
View ArticleClik here to view.
adm1278 FET power limit and design tool
Hello,In the datasheet of ADM1278, there is a equation for FET power limit, it's a little bit confused about the unit. I think it should be power, but what does mean 8 and 50 in the equation? I also...
View ArticleADP5589 question
Dear Sir,ADP5589 have driver for windows10 mobile?ADP5589 have EVM document? Thanks.
View ArticleADM1178 - Can it be turned on and off via I2C?
Hi,We are planing to use the ADM1178 Hot swap controller in a new design and want to control it fully via the I2C interface. The Datasheet does not provide enough information if this is possible....
View ArticleADP1613 and ADM7150 layout suggestions
Hello, I'm designing a power supply for data acquisition device which needs clean 5V. I decided to use ADP1613 and ADM7150 ICs to get 6.2V from SEPIC DC/DC converter and 5V from LDO. Power requirement...
View ArticleADM8614 power up question
What behavior should I expect when the ADM8614 is powered up with the WD_DIS line high? I'd like it to star the WDT function when the WD_DIS line goes low. My real problem is that the reset period...
View ArticleClik here to view.
ADM1278 IBIS model request
Dear Sir, We need IBIS model of ADM1278 for simulation. Could you provide it to me? Thanks!
View ArticleClik here to view.
ADP5071 layout data
Hello Our customer will use ADP5071 and is evaluating EVAL-ADP5071.He requests that brd file of EVAL-ADP5071 for design referrence.Please give me its brd file . Regards,Terumasa
View ArticleClik here to view.
ADP3303 No regulation
Hello. I am connected linear regulator ADP3303 like in first cheme in datasheet, but it didn't work. I tried everything, changed 3 ADP3303, But it's still have output voltage the same as input. My...
View ArticleClik here to view.
Different of ADUM7223
Are the IC ADUM7223ACCZ, ADUM7223BCCZ, ADUM7223CCCZ the same?or what's different ??
View ArticleClik here to view.
IC required for power supply management for a development which is generic...
Please could you let me know the best IC for power mangement in a generic development board.Which should supply multiple voltage, current sources. Voltage measurement etc etc.
View ArticleClik here to view.
output error when using ADP5054,PLEASE HELP!
to be simple,i have designed one circuit according to adp5054 ref,the setting as follows:input:12voutput:mode:FPWMfreq:600khzch1:1.2vch2:1.4vch3:2.5vch4:3.3vthe circuit as follows:and now a part of...
View ArticleClik here to view.
ADP7182 adj issue
Hi there,We are using ADP7182 and trying to adjust Vout to -1.8V from -25V input but currently we only can get about -2.5V output with Resistor 60.4KOhm and 110KOhm. any suggestion on this? Thank you.
View ArticleClik here to view.
different result's between ADIsimPE and Diff Amp Calculator!!!
hi every one.I have some issue's with this soft ware's...I am designing a single ended to differential converter with AD4940.the Diff Amp Calculator shows that Band Width of circuit is 24Mhz but with...
View ArticleADR444BRZ output voltage decreased with increasing temperature
Hi, we got a problem when using ADR444BRZ, the output voltage decreased with increasing temperature. Attached pleased find the circuit diagram we used. It has worked well for 4 years, but now we find...
View Article