Clik here to view.
Is there a pdf download for the AD505X Evaluation board schematic only and...
Hello everyone, The user guide pdf document ( 1845201.pdf) for the Evaluation board has an insert of the schematic and layout but they are not very clear. Where can I find the actual pdf for the...
View ArticleLooking for replacement for ADI911 and ADI904
I'm looking for replacement voltage regulators for part numbers ADI911 and ADI904. Are any available?
View ArticleClik here to view.
False Key Detection in ADP5585
HI all.,We are facing a false key detection on our product. We are using the Keypad Decoder ADP5585 IC for the KEypad logic on our product. The datasheet of ADP5585 specifies that a Key press will be...
View ArticleADM1064 'Reserved State'
Hello, Please could anyone tell me what sets of conditions could force the ADM1064 to enter the 'Reserved' state? Thank you. Regards,Phil
View ArticleADN8831 FET Requirements
Hi, I am trying to choose the MOSFETs for ADN8831, but for better efficiency I would like to use ones with lower R_DS,ON than the one suggested in AN-695. Can I use the guideline given in "External FET...
View ArticleCan't find Comparator AD790 in ADIsimPE Library
How can I simulate AD790 if it's not in the library and AD website does not have spice model?
View ArticleADN8831 Cooling Problem
I recently started testing my ADN8831-EVALZ board for its heating and cooling control ability.I am currently using a 10k NTC thermistor. I can successfully heat the target device. However, when I try...
View ArticleADP2504 EVB Board Gerber File
Dear All:I would like to referADP2504 EVB Board PCB Layout design. Can you provide "UG-038 ADP2504 FIX Output type" &"UG-060 ADP2504 ADJ Output type" Gerber Files to me refer.?Thanks Best Regards,...
View ArticleClik here to view.
ADP5071 EVB Board Gerber
Dear All:I need to reference ADP5071 EVB Board PCB Layout design, can give me ADP5071 EVB Board Gerber File reference? thanks~ Best Regards,Cuttlefish
View ArticleClik here to view.
How to get a 4.5V reference voltage from ADR02?
hi; I saw in the datasheet of ADR02 that if we add a 10K pot at the trim pin, we can get 4.95V to 5.02V, but how can I extend the range down to 4.5V? THX! Donald
View ArticleClik here to view.
ADP5090 output power rating
Hi May I know the power rating for ADP5090-2-EVALZ that is a Evaluation Board with Solar Harvester ??if we setting 3.3Vout , how much the iout ??
View ArticleClik here to view.
ADuM5010 Viso voltage
The datasheet indicates the Viso voltage is...1.23V*(R1+R2)/R1. What is the typical and maximum tolerance of the internal 1.23V reference voltage ?
View ArticleClik here to view.
High voltage digital potentiometer
Hello, I'm looking for a digital potentiometer that has an analog rail that can handle a voltage of 60V.Does such a thing exist? if so then where can I find it? Thanks much!omer
View ArticleADN8831 FET Requirements
Hi, I am trying to choose the MOSFETs for ADN8831, but for better efficiency I would like to use ones with lower R_DS,ON than the one suggested in AN-695. Can I use the guideline given in "External FET...
View ArticleCan't find Comparator AD790 in ADIsimPE Library
How can I simulate AD790 if it's not in the library and AD website does not have spice model?
View ArticleADP1853 spice model
Dear,is there available SPICE model for ADP1853 ?(I'm not interested in web-based simulation tools since my topology is not standard and requires models of external devices.)Thanks in advance...
View ArticleClik here to view.
battery polarity protection circuit
Dear sir,we are using 15 v battery.we are wish to add battery polarity protection circuit..is there any simple circuit for this1.if we give 15v zener diode across is it enough?it will working below or...
View ArticleClik here to view.
typo? of XPE power estimation
Dear Sir/Madam, I just found typo(maybe) on your brochure BR10508-3-2/15(B) page-9. As for your the chart of "XPE Power Estimation---Use Case for Xilinx Artix-7/Kintex-7", Family Virtex-7 ===>...
View ArticleClik here to view.
Eval-ADuM5010EBZ gerber file
Hi , we would like to have Eval-ADuM5010EBZ gerber file for our new design reference. plz share with us the gerber file . thanks
View Articledigital control of simpler, lower power supplies ref designs
I appreciate the raw power with flexible interface that the ADI Digital Power suite offers - but I am curious about simpler designs in compact form factor with tight control, monitoring, and the like....
View Article